收藏本站

Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADP1829
FB1
1
24
POK1
SYNC
FREQ
GND
UV2
FB2
COMP2
TRK2
2
3
4
5
6
7
8
PIN 1
INDICATOR
ADP1829
TOP VIEW
(Not to Scale)
23
22
21
20
19
18
17
BST1
DH1
SW1
CSL1
PGND1
DL1
PV
NOTES
1. THE EXPOSED PAD MUST BE CONNECTED TO AGND.
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Mnemonic
FB1
SYNC
FREQ
GND
UV2
FB2
COMP2
TRK2
SS2
POK2
BST2
DH2
SW2
CSL2
PGND2
DL2
PV
DL1
PGND1
CSL1
SW1
DH1
Description
Feedback Voltage Input for Channel 1. Connect a resistor divider from the buck regulator output to GND and tie
the tap to FB1 to set the output voltage.
Frequency Synchronization Input. Accepts external signal between 600 kHz and 1.2 MHz or between 1.2 MHz
and 2 MHz depending on whether FREQ is low or high, respectively. Connect SYNC to ground if not used.
Frequency Select Input. Low for 300 kHz or high for 600 kHz.
Ground. Connect to a ground plane directly beneath the ADP1829. Tie the bottom of the feedback dividers to
this GND.
Input to the POK2 Undervoltage and Overvoltage Comparators. For the default thresholds, connect UV2
directly to FB2. For some tracking applications, connect UV2 to an extra tap on the FB2 voltage divider string.
Voltage Feedback Input for Channel 2. Connect a resistor divider from the buck regulator output to GND and
tie the tap to FB2 to set the output voltage.
Error Amplifier Output for Channel 2. Connect an RC network from COMP2 to FB2 to compensate Channel 2.
Tracking Input for Channel 2. To track a master voltage, drive TRK2 from a voltage divider from the master
voltage. If the tracking function is not used, connect TRK2 to VREG.
Soft Start Control Input. Connect a capacitor from SS2 to GND to set the soft start period.
Open-Drain Power OK Output for Channel 2. Sinks current when UV2 is out of regulation. Connect a pull-up
resistor from POK2 to VREG.
Boost Capacitor Input for Channel 2. Powers the high-side gate driver DH2. Connect a 0.22 μF to 0.47 μF
ceramic capacitor from BST2 to SW2 and a Schottky diode from PV to BST2.
High-Side (Switch) Gate Driver Output for Channel 2.
Switch Node Connection for Channel 2.
Current Sense Comparator Inverting Input for Channel 2. Connect a resistor between CSL2 and SW2 to set the
current-limit offset.
Ground for Channel 2 Gate Driver. Connect to a ground plane directly beneath the ADP1829.
Low-Side (Synchronous Rectifier) Gate Driver Output for Channel 2.
Positive Input Voltage for Gate Driver DL1 and Gate Driver DL2. Connect PV to VREG and bypass to ground with
a 1 μF capacitor.
Low-Side (Synchronous Rectifier) Gate Driver Output for Channel 1.
Ground for Channel 1 Gate Driver. Connect to a ground plane directly beneath the ADP1829.
Current Sense Comparator Inverting Input for Channel 1. Connect a resistor between CSL1 and SW1 to set the
current-limit offset.
Switch Node Connection for Channel 1.
High-Side (Switch) Gate Driver Output for Channel 1.
Rev. C | Page 7 of 28
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
R1S-1515/P-R CONV DC/DC 1W 15VIN 15VOUT
ADP2102-1.8-EVALZ BOARD EVAL FOR ADP2102-1.8
ECM10DCMD-S288 CONN EDGECARD 20POS .156 EXTEND
ADP2102-1.875EVALZ BOARD EVAL FOR ADP2102-1.875
195D685X0016X2T CAP TANT 6.8UF 16V 20% 2910
A9BAG-1108F FLEX CABLE - AFF11G/AF11/AFE11T
GEM12DSES-S243 CONN EDGECARD 24POS .156 EYELET
EBM08DCCN-S189 CONN EDGECARD 16POS R/A .156 SLD
相关代理商/技术参数
ADP1850 制造商:AD 制造商全称:Analog Devices 功能描述:Wide Range Input, Dual/Two-Phase, DC-to-DC Synchronous Buck Controller
ADP1850ACPZ 制造商:Analog Devices 功能描述:IC BUCK CNTRL SYNC 2PH 32LFCSP
ADP1850ACPZ-R7 功能描述:IC REG CTRLR BUCK PWM CM 32LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
ADP1850DP-EVALZ 功能描述:EVAL BOARD FOR ADP1850DP RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND
ADP1850SP-EVALZ 功能描述:EVAL BOARD FOR ADP1850SP RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ADP1851ACPZ-R7 功能描述:电流型 PWM 控制器 w-range input Synch StepDown DC/DC Cntr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
ADP1851-EVALZ 功能描述:电源管理IC开发工具 Evaluation Board 1.8V 25A Output RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
ADP1853 制造商:AD 制造商全称:Analog Devices 功能描述:Synchronous, Step-Down DC-to-DC Controller